Termékek pvc bevonat anyagok (24)

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Materiał powlekany PCW tapicerski. Wytrzymały i łatwy w utrzymaniu czystości. Główne zastosowania: meble tapicerowane, pufy, legowiska dla psów, materace gimnastyczne.

Ming Xiao Manufacturing Co Ltd ist spezialisiert auf Kunststoffextrusionsprofile, Rohre, Stangen, Schienen, LED-Lampenschirm, Kabelkanäle, Lautsprecherkörper, Arten von Schalen und Objektträgern. Wir können Kunststoffextrudionsprodukte aus Materialien aus PVC, ABS, PP, PE herstellen. PC, PMMA, AS / PE ... Die Kunststoff-Extrusionsprofile werden häufig für Autoteile, Stadtbahnzüge, Lampen und Laternen, die Kühlindustrie, elektrische Haushaltsgeräte, Schreibwaren, Lager und andere Unternehmen verwendet, um qualitativ hochwertige Unterstützungsdienste bereitzustellen. Wenn Sie Kunststoffextrusionsprofile benötigen, senden Sie uns bitte Ihre Zeichnungen und Muster für ein Angebot.

PVC-Compound ist für die liegende Weinlagerung geeignet und bietet einen hohen Schutz gegen den entstehenden Innendruck durch Temperaturunterschiede, sowie bei kohlensäurehaltigen Getränken. PVC-Compound formt sich tiefenrein an.

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

When the going gets tough in industry and production, protective coatings of particularly high quality are always in demand. For industrial applications, FreiLacke liquid coatings provide highly effective solutions for the coating of all surfaces that need to withstand heavy stresses. Whether such heavy stresses are due to corrosion, chemicals or weather influences, FreiLacke provides the optimum protective coating for all areas of application. For example, these can be for machines and systems used within the production area, or for construction machinery, containers, wheels, piping systems and many other items. An extra benefit that you should take advantage of: As a leading system supplier, FreiLacke develops and produces all coatings under one roof. This makes FreiLacke your ideal partner for all industrial surface coatings.

Die Entscheidung für das richtige System Anforderungen an Böden durch zahlreiche Bewegungs- und Herstellprozesse sowie Beanspruchungen durch Chemikalien kann man häufig nur durch den Einbau einer Kunstharzbeschichtung bzw. eines Kunstharzbelages begegnen. Zudem greifen oftmals rechtliche Vorschriften, die den Einbau einer/eines Kunstharzbeschichtung/-Belages fordern. Bei der Auswahl eines geeigneten Systems sind insbesondere folgende Parameter zu berücksichtigen: • Anforderungen an die Pflege und Reinigung • Langlebigkeit • Forderung einer Rutschhemmungsklasse • Forderung nach Rissüberbrückung • optisches Erscheinungsbild, Farbgestaltung • Forderung nach Ableitfähigkeit • Anforderungen an eine Nichtentflammbarkeit • Lebensmittelneutralität • Anforderungen an die chemische Beständigkeit Lassen Sie sich durch uns individuell zu dem für Sie erforderlichen System beraten.

Durch individuelle und auftragsbezogene Produktion von Halbzeugen können wir die Möglichkeiten hier nur in Grenzen aufzeigen. Werkstoffe PE, PP, PS, ABS, PVC, PET usw.

PVC SANDWICH PANELS

I rivestimenti in PVD e CVD garantiscono un'ottima adesione al metallo duro ed una maggiore durata del prodotto. Essi possono essere applicati su richiesta del Cliente su trafile, spalle, sellette e blocchetti.

1,5 mm tel üstüne pvc kaplama işlemidir. Özel üretim ürünümüzdür.

PVC DUVAR VE TAVAN KAPLAMALARI

1,5 mm telin üstüne yapılan PVC kaplamadır. Özel üretimdir.

Beschichtbar sind Feinblech, Baustahl (auch verzinkt), Alu-Blech, Alu-Druckguss, Magnesiumguss, Glas und Kunsttsoff, in Abhängikeit von der Temperaturbeständigkeit. Pulverlacke sind lösungsmittelfrei und werden mit elektrostatischen Spritzpistolen aufgebracht und je nach Empfindlichkeit und Chemie der Pulverlacke und der zu beschichteten Teile werden sie zwischen 130 und 220°C ausgehärtet. Folgende Vorbehandlungen sind möglich: • Gelb - und Grünchromatierung • Zinkphosphatierung • chromfreie Konversation Vorteile • hochwertiger Korrosionsschutz • stark mechanisch belastbar • keine Umweltprobleme, da lösungsmittelfrei und Rückgewinnung des Oversprays • sehr gute chemische Beständigkeit • hohe Steinschlagfestigkeit • als Polyesterpulver sehr UV-beständig • dekorative Oberflächen in fast allen Farbtönen, Glanzgraden und Strukturen

Technische Kunststoffprofile

Technische Kunststoffe

Silicon nitride is one of the hardest ceramics but also one of the most resistant. Si3N4 is mainly used in severe environments which combine extreme temperatures with abrasive and/or corrosive medium. Silicon nitride can be of different grades : sintered, hot pressed or reaction bonded. Selection of materials Microcertec offers two high-purity Si3N4 grades that are particularly suited for hostile environments : sintered silicon nitride hot pressed silicon nitride Both Si3N4 materials are mainly designed to be used in thermal-mechanical or corrosion-resistance applications because they show an outstanding behaviour to resist to wear, thermal shocks and corrosion (liquids and gases). Moreover, these pure Si3N4 grades offer a low thermal expansion. Properties Sintered silicon nitride and HP Si3N4 have the following properties : low density excellent thermal shock resistance excellent wear resistance excellent corrosion resistance (liquids and gas) low coefficient of thermal...

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Materiał powlekany o wysokiej odporności na działanie promieniowania UV jak również wody morskiej i chlorowanej. Powierzchnia zabezpieczona przed wzrostem pleśni. Materiał trudnopalny (papieros / zapałka). Może być produkowany w wersji odpornej na niskie temperatury do -30st. C

Eko-skóra o zastosowaniu jako materiał obiciowy dla mebli tapicerowanych jak sofy, krzesła czy fotele. numer artykułu:SI/B

Tkanina powlekana PCW do wykorzystania do MEBLI BIUROWYCH (FOTELE, KRZESŁA, SOFY) V-4 numer artykułu:V-4

Ekoskóra o delikatnie zarysowanej strukturze, charakteryzująca się niezwykłą miękkością, elastycznością i przyjemnością w dotyku. To materiał tapicerski, który wyróżnia się wysoką odpornością na ścieranie i odkształcenia, długotrwałą trwałością oraz niezawodną odpornością. Sprawdza się jako materiał obiciowy do mebli tapicerowanych czy tapicerki samochodowej. Może być również stosowany jako materiał kaletniczy.

MEBLE DO ODPOCZYNEK (ŁÓŻKA, SOFY, FOTELE) - model FSO Soft, który charakteryzuje się bardzo miłym, "suchym" dotykiem. Powierzchnia odporna za zarysowania. Na życzenie klienta wyrób może być wyprodukowany w wersji trudnopalnej, co jest szczególnie ważne do miejsc użyteczności publicznej.

PVC tavan ve duvar kaplamaları